MSX Village forum

 
By enribar:
Hi friend, ok I'll try to dump this evening, with many other roms.
I will use ASCII's Game Reader and dvik & joyrex tools: http://www.dvik-joyrex.com/tools.html
 

 
[General]
Id=MSX - Toshiba HX-22
Manufacturer=Toshiba
Model=HX-22
System=MSX
KeyLayout=japanese
RomSetVersion=1
 
[Video]
version=TMS99x8A
vram size=16kB
 
[CMOS]
Enable CMOS=0
Battery Backed=0
 
[Subslotted Slots]
slot 0=0
slot 1=0
slot 2=0
slot 3=1
 
[External Slots]
slot A=1 0
slot B=2 0
 
 
[FDC]
Count=2
[CPU]
Z80 Frequency=3579545Hz
[Board]
type=MSX
[Slots]
0 0 0 0 84 "" ""
0 0 0 0 24 "Machines/MSX - Toshiba HX-22/hx22kfn.rom" ""
0 0 0 4 20 "Machines/MSX - Toshiba HX-22/hx22bios.rom" ""
3 0 0 8 23 "" ""
3 3 2 4 42 "Machines/MSX - Toshiba HX-22/hx22word.rom" ""
[AUDIO]
PSG Stereo=1
PSG Pan channel 0=center
PSG Pan channel 1=left
PSG Pan channel 2=right

 
Extended Basic Manual for Japanese HX-20/HX-21/HX-22
 
Printer Spooler : only HX-20 series
CALL SPOLON
CALL SPOLOFF
CALL LCOPY
 
RAM disk (device name is MEM: or MEM0: ) : only HX-20 series (but similar to MSX2)
CALL MEMINI
CALL MEMOFF
CALL MFILES
CALL MKILL
CALL MNAME
 
SAVE
LOAD
RUN
MERGE
 
OPEN
CLOSE
PRINT#
PRINT# USING
INPUT#
LINE INPUT#
 
INPUT$
EOF
LOC
LOF
 
RS232C (device number is 0 , device name is COM0: ) : MSX standard RS-232C extensions
CALL COMINI
CALL COMTERM
CALL COMDTR
CALL COMBREAK
CALL COMSTAT
CALL COM GOSUB
CALL COMON
CALL COMOFF
CALL COMSTOP
 
SAVE
LOAD
RUN
MERGE
 
OPEN
CLOSE
PRINT#
PRINT# USING
INPUT#
LINE INPUT#
 
EOF
INPUT$
LOC
LOF
 
Japanese Word Processor "Kanji-Kun" : HX-M200(KANJI ROM) is needed
CALL JWP
 
Example :
CALL COM(,GOSUB 1100)
CALL COMBREAK(,10)
CALL COMBREAK
CALL COMDTR(,0)
CALL COMINI
CALL COMINI("0:8N" )
CALL COMINI("0:",4800)
CALL COMINI("0:",,,100)
CALLCOMINI("0:8N3XNNNN",4800,,5)
CALL COMSTAT("0:",F) : PRINT BIN$(F)
CALL COMTERM("0:" )
 
COMINI has many parameters, eight characters and three numbers.
 
character length: "5" , "6" , "7" , "8"
parity: "E" , "O" , "I" , "N"
stop bit length: "1" , "2" , "3"
Xon/off control: "X" , "N"
CS control: "H" , "N"
add LF when CR is recieved: "A" , "N"
delete LF when CRLF is sent: "A" , "N"
SI/SO control (for Japanese "katakana" characters): "S" , "N"
baud rate (recieve): 50,75,110,300,600,1200,1800,2000,2400,3600,4800,7200,9600,19200 or negative number
baud rate (send): same as above
wait time: 0 to 255

 
COMMANDCHARACTER
Chapter Inquiryv
Chapter Modei
Clear AllV
Resume the mode prior to Stilla
CX Noise Reduction Onn
CX Noise Reduction Offo
Open the disc compartment*
Fast Forward;
Frame Advance+
Frame ModeU
Frame Reverse,
Forward Scan>
Forward Skip -
Forward Slow<
Variable forward play=
Index OnP
Index OffQ
Memorize the current locationZ
Locate the memorized location[
Set mark positions
MenuB
Start-up spindle motorb
Stop spindle motorc
Audio mute on$
Audio Mute off%
Play:
RepeatD
RewindK
Reverse PlayJ
Scan in reverseN
Reverse skip.
Slow reverse playL
Variable reverse playM
StillO
Stop?